Yamaha YZF R1/R1M 2020

$20.00 – $350.00

SKU: F750 Category: Yamaha

Description
Additional information

Notes	Installation Rating	Downloads	Instructions
As of October 2020, this kit now runs ALL 8 injectors The EXUP valve must be removed to install kit. Order part no. E741 Improvements in Air/Fuel Ratio throughout Smoother throttle response Power gains in lower, mid and upper region. One T-tap: +12v SW		Fuel Map Database	Z-Fi Lower Injector Connector Installation

Weight	1.5 lbs
Dimensions	8 × 8 × 6 in
Available Products	Z-Fi Fuel Controller [#F750], Map Select Switch [#A868], Pair Valve Eliminator Kit [#E560], EXUP Eliminator [#E741], Z-AFM self fuel mapping module [#ZAFM49]

You may also like…

Map Select Switch
$80.00

To our customers and dealers,

The Bazzaz team would like to thank you for the many years of support and loyalty to our products.

As of 1/1/22 Bazzaz will no longer offer support for the Bazzaz engine management line (Z-Fi, Z-Fi TC, QS4, ZAFM).

Although YFI racing will not be offering technical support for Bazzaz products except for customers who purchased directly from YFI Racing, many QS4 kits, accessories, and spare parts will be available through them. www.yfi-racing.com.

You can also contact YFI Racing at sales@yfi-racing.com if you do not find what you are looking for on their site.

The Bazzaz website will remain to offer customers access to installation instructions, fuel map database, and technical support documents. The technical support documents utilize the same diagnosis steps that the Bazzaz technical support team has worked from since the beginning so they should be very helpful.

The Big Three: double-check these three common culprits:

The Bazzaz ground lug is properly secured to a non-insulating chassis ground. Test this by temporarily grounding the Bazzaz ground lug directly to the battery negative terminal and checking to see if this resolves the issue.
The vehicle has fuel and there are no obstructions (such as a fuel line kink) that could affect fuel delivery.
The Bazzaz control unit powers up. Turn the key on and the control unit should illuminate blue. If it does not, re-check the 12V power source connection

Bazzaz tuning software and software manual
https://bazzaz.net/software/software-overview/

Principia dyno software and software manual
https://bazzaz.net/software/principia-software-side/

Fuel map database
https://bazzaz.net/fuel-map-database/

Engine management wire color guide
https://bazzaz.net/wp-content/uploads/2018/11/kb-bazzaz-wiring-diagram-1.pdf

Not starting or running properly
https://bazzaz.net/wp-content/uploads/2018/11/not_starting-2.pdf

Quick shifter troubleshooting
https://bazzaz.net/wp-content/uploads/2018/11/QS_Cutting_Out.pdf

Software troubleshooting
https://bazzaz.net/wp-content/uploads/2018/11/Z-Mapper-software-troubleshooting-1.pdf

Traction control settings
https://bazzaz.net/wp-content/uploads/2018/11/kb-bazzaz-traction-control-supplement-1.pdf

Traction control troubleshooting
https://bazzaz.net/wp-content/uploads/2018/11/tc_trouble_shoot-2.pdf

ZAFM troubleshooting
https://bazzaz.net/wp-content/uploads/2018/11/zafm_flow_chart-2.pdf

ZAFM O2 sensor installation
https://bazzaz.net/wp-content/uploads/2018/11/O2sensor-data-sheet-2.pdf

Z Bomb integration
https://bazzaz.net/wp-content/uploads/2018/11/kb-bazzaz-z-bomb-integration-1.pdf